新聞資訊
冷卻速度對GH4169合金凝固過程微觀偏析及糊狀區穩定性的影響
發布人：上海艾荔艾金屬材料有限公司m.85978597.cn
更新時間：2015-08-25
通過不同冷卻速度下的凝固重熔試驗，結合SEM微觀分析及電子探針成分分析，研究GH4169合金凝固過程微觀偏析的演化規律，分析凝固前沿液相區的密度變化規律，并提出基于相對Rayleigh數的凝固前沿糊狀區的穩定性判據。
冷卻速度對GH4169合金凝固過程微觀偏析及糊狀區穩定性的影響Effect of cooling rate on microsegregation behaviors and
mush zone stability of GH4169 alloy during solidification process
通過不同冷卻速度下的凝固重熔試驗，結合SEM微觀分析及電子探針成分分析，研究GH4169合金凝固過程微觀偏析的演化規律，分析凝固前沿液相區的密度變化規律，并提出基于相對Rayleigh數的凝固前沿糊狀區的穩定性判據。結果表明：冷卻速度低于0.05
℃/s時，液相中的Nb含量隨出爐溫度的下降很快升高到一個較高值，在較低溫度出爐冷卻時，Nb含量迅速升高到14%以上，可達合金名義成分中Nb元素含量的3倍；提高冷卻速度至0.1
℃/s，高溫出爐時，Nb含量升高很慢，當出爐溫度低于1 310 ℃時，
Nb含量迅速升高到10%以上；進一步提高冷卻速度，殘余液相中Nb元素含量變化不大，與合金的名義成分接近。當冷卻速度較高時(大于0.1
℃/s)，GH4169合金凝固過程凝固前沿糊狀區的穩定性較好，相對Rayleigh數較低；而當冷卻速度較低時，即低于0.02℃/s時，凝固前沿糊狀區穩定性判據Rv值比較高，而且在1
330
℃附近出爐冷卻時，存在一個峰值區，最大峰值接近7.5×10-13。說明當凝固過程冷卻速度較低時，元素的微觀偏析使得GH4169合金凝固前沿糊狀區的穩定性降低，可能導致微觀偏析向宏觀偏析轉變。
The microsegregation behaviors of GH4169 alloy during its
solidification process were investigated by remelting tests, SEM and EMPA
analysis. Furthermore, the density variation for the solidification front of
this alloy was analyzed and a stability criterion based on relative Rayleigh
number model was put forward. The results show that, when the cooling rate is
lower than 0.05 ℃/s, Nb content in the residual liquid phase increases with
decreasing the pouring temperature, it can reach 14%, three times of the
designed Nb content for this alloy. When the cooling rate increases to 0.1 ℃/s
and the pouring temperature is lower than 1 310 ℃, Nb content in the residual
liquid phase reaches 10% promptly, while when the pouring temperature is higher
than 1 310 ℃, Nb content in the residual liquid phase varies slowly. With the
increase of cooling rate during the solidification process, Nb content in the
residual liquid phase can decrease to the designed value gradually. At the same
time, a heavier microsegregation of Nb element may occur at lower cooling rate
in the mush zone for GH4169 during its solidifying process, resulting in the
bigger relative Rayleigh number and the worse stability of mush zone, which may
increase the probability of freckle formation.
以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://m.85978597.cn，轉載請注明出處。
前一頁：固溶溫度對7B50鋁合金組織與性能的影響
后一頁：美國研發出新型輕質高強金屬