新聞資訊
焊后熱處理對Al-Mg-Si-Cu合金激光焊接接頭微觀結構和力學性能的影響
發布人：上海艾荔艾金屬材料有限公司m.85978597.cn
更新時間：2015-09-28
采用電子顯微學方法和力學性能測試，探究180℃下焊后時效處理工藝對Al-Mg-Si-Cu合金激光焊接接頭微觀結構和力學性能的影響。
焊后熱處理對Al-Mg-Si-Cu合金激光焊接接頭微觀結構和力學性能的影響Effects of post-weld heat treatment on microstructure andmechanical properties of laser-beam welded Al-Mg-Si-Cu alloy
采用電子顯微學方法和力學性能測試，探究180℃下焊后時效處理工藝對Al-Mg-Si-Cu合金激光焊接接頭微觀結構和力學性能的影響。結果表明：經過焊后熱處理的焊件焊接接頭的力學性能得到一定程度的提升，但焊縫處由于在焊接過程中形成大量的第二相顆粒，消耗了大量的溶質原子，因此，焊接接頭硬度最低。對于焊前處理為欠時效的焊件，熱影響區硬度經過焊后熱處理后完全恢復母材硬度水平；而對于焊前處理為峰值時效和過時效的焊件，熱影響區硬度不能完全恢復，會出現一個硬度谷，即軟化區。通過對軟化區進行透射電鏡表征后發現，該區域內析出相出現明顯的粗化。
The effect of post-weld artificial aging at 180℃ on the microstructure and mechanical properties of laser-beam welded Al-Mg-Si-Cu alloy was investigated. The results show that the mechanical properties of the joint after post-weld heat treatment can be enhanced to some extent compared to the as-welded joint, while the hardness of the weld seam is still the lowest region because the formation of massive second particles during the welding process consumes many solute atoms needed to form strengthening precipitates. The hardness of heat-affected zone in the joint under-aged before welding can be fully recovered to that of base metal after post-weld heat treatment. While the hardness of heat-affected zones in the joint peak-aged and over-aged before welding can not be fully recovered after post-weld heat treatment, in these heat-affected zones, the hardness grooves, typical of softening zones, occur in the hardness profiles. The precipitates in the softening zone coarsen apparently as revealed by transmission electron microscopy (TEM).
以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://m.85978597.cn，轉載請注明出處。