新聞資訊
7B04鋁合金薄板的攪拌摩擦焊接及接頭低溫超塑性研究
發布人：上海艾荔艾金屬材料有限公司m.85978597.cn
更新時間：2015-10-26
在轉速 1600r/min-焊速 200mm/min、轉速 800 r/min-焊速 200mm/min、轉速 400 r/min-焊速 400mm/min 三組參數下對 2 mm 厚的退火態 7B04 鋁合金薄板進行攪拌摩擦焊接，研究了焊接參數對焊縫質量及微觀組織的影響，并分析了焊核區的低溫超塑性變形行為。
7B04鋁合金薄板的攪拌摩擦焊接及接頭低溫超塑性研究FRICTION STIR WELDIING AND LOW-TEMPERATURE ?SUPERPLASTICITY OF 7B04AL SHEET
在轉速 1600r/min-焊速 200mm/min、轉速 800 r/min-焊速 200mm/min、轉速 400 r/min-焊速 400mm/min 三組參數下對 2 mm 厚的退火態 7B04 鋁合金薄板進行攪拌摩擦焊接，研究了焊接參數對焊縫質量及微觀組織的影響，并分析了焊核區的低溫超塑性變形行為。結果表明，通過控制焊接參數，可獲得良好的焊接質量，接頭強度系數達100%。焊核區發生動態再結晶，生成細小等軸晶，母材晶粒尺寸約為 300 μm，轉速為 1600、800 和 400r/min 時對應晶粒尺寸分別為 2、1 和 0.6μm。這種細晶組織有利于焊核區超塑變形，在300 oC，焊核區在1×10-3和 3×10-4 s-1應變速率下獲得了160%~590%的延伸率，在 350 oC、1×10-3 s-1條件下獲得高達790%的最大延伸率，在約 400 oC時超塑性變形行為消失。?
Annealed 7B04 Al sheets in thickness of 2 mm were subjected to friction stir welding?(FSW) under three rotation rate-welding speed parameters of 1600 rpm-200 mm/min, 800 rpm-200?mm/min, and 400 rpm-400 mm/min, respectively. The effect of welding parameters on the tensile?property and microstructure of the FSW joints were investigated, with more efforts focusing on the?low-temperature superplasticity of the nugget zones (NZs). The results showed that FSW joints with?high quality could be produced by controlling welding parameters, with a joint strength coefficient of?100% being obtained. Dynamic recrystallization took place in the NZs with fine and equiaxed grains?generated. The grain size of the base material was about 300 μm, while it was significantly decreased?in the NZs with decreasing the rotation rate: about 2 μm, 1 μm and 0.6 μm for the above three?samples, respectively. The fine grain structure of the NZs could facilitate their superplastic?deformation. The NZs exhibited superplastic elongations ranged from 160% to 590% at 300 oC at?strain rates of 1×10-3 s-1 and 3×10-4?s-1. The maximum superplasticity of 790% was obtained at 350 oC?at the strain rate of 1×10-3 s-1. The ability to superplastic deformation disappeared in the NZs at 400?oC.?
以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://m.85978597.cn，轉載請注明出處。