新聞資訊
擠壓態AM30鎂合金的動態力學行為及變形機制
發布人：上海艾荔艾金屬材料有限公司m.85978597.cn
更新時間：2015-12-16
采用分離式Hopkinson壓桿和反射式拉桿裝置在室溫對擠壓態AM30鎂合金進行動態壓縮和拉伸試驗，分析AM30鎂合金在沿?cái)D壓方向(ED)和橫向(TD)壓縮和拉伸時的變形機制，計算AM30鎂合金在ED和TD方向壓縮和拉伸時的應變速率敏感系數，并通過SEM觀察斷口形貌。
擠壓態AM30鎂合金的動態力學行為及變形機制Dynamic mechanical behavior and deformation mechanism of?extruded AM30 magnesium alloy
采用分離式Hopkinson壓桿和反射式拉桿裝置在室溫對擠壓態AM30鎂合金進行動態壓縮和拉伸試驗，分析AM30鎂合金在沿?cái)D壓方向(ED)和橫向(TD)壓縮和拉伸時的變形機制，計算AM30鎂合金在ED和TD方向壓縮和拉伸時的應變速率敏感系數，并通過SEM觀察斷口形貌。結果表明：沿ED方向壓縮時，拉伸孿晶{ }á ?是主要變形機制，屈服強度對應變速率不敏感；沿ED方向拉伸以及TD方向壓縮和拉伸時，拉伸孿晶不能啟動，位錯滑移參與變形，應變速率敏感系數提高；AM30鎂合金在ED方向表現出很強的拉壓不對稱性，壓縮/拉伸屈強比約為0.38，在TD方向則無明顯的拉壓不對稱性；AM30鎂合金在動態壓縮和拉伸時斷口形貌呈韌脆混合的斷裂特征。
The dynamic compressive and tensile tests on the extruded AM30 magnesium alloy were carried out at room temperature using a split Hopkinson pressure bar and a reflected Hopkinson tension bar apparatus. The deformation mechanisms of the AM30 magnesium alloy under the dynamic compression and tension loading along the extruding direction (ED) and the transverse direction (TD) were analyzed. The strain rate sensitivity coefficients of the alloy under different conditions were calculated and the dynamic fractograph of the alloy was analyzed. The results show that, when the alloy is compressed along the ED, tension twining { }á ? is the main deformation mechanism, and the yield stress of the alloy is insensitive to the strain rate. When the alloy is tested under tension along the ED and under tension and compression along TD, tension twining { }á ? is not initiated, while the dislocation slip is responsible for the plastic deformation, resulting in the fact that the strain rate sensitivity becomes higher. The asymmetry of the tension-compression of AM30 magnesium alloy is much pronounced along the ED and the yield stress ratio of compression to tension is about 0.38. The fractograph of the alloy is mix-fractured morphology under dynamic compressive and tensile conditions.
獲取更多我們供應的合金和服務信息，請致電086-021-67660801或發電子郵件kefu@ailiaigroup.com聯系我們，您也可以通過微博和微信和我們互動。
For more information on the alloys and services that we supply,?call us?at 086-021-67660801 or email us at kefu@ailiaigroup.com. You can also get in touch on social media, we are constantly active on?Weibo?and?Weixin.