新聞資訊
熱處理制度對2056鋁合金微觀組織和抗應力腐蝕性能的影響
發布人：上海艾荔艾金屬材料有限公司m.85978597.cn
更新時間：2015-12-16
采用光學顯微分析、掃描電鏡及透射電鏡觀察、慢應變速率拉伸測試等研究2056鋁合金在T6、T851及T351熱處理狀態下的微觀組織和抗應力腐蝕性能。
熱處理制度對2056鋁合金微觀組織和抗應力腐蝕性能的影響Effect of heat treatment on microstructure and resistance to?stress corrosion cracking of aluminum alloy 2056
采用光學顯微分析、掃描電鏡及透射電鏡觀察、慢應變速率拉伸測試等研究2056鋁合金在T6、T851及T351熱處理狀態下的微觀組織和抗應力腐蝕性能。結果表明：2056合金在T6態下，晶內析出相主要為粗大的S′相和少量粗大的含錳相，抗拉強度為445.13 MPa，晶界析出相粗大且呈非連續分布，無沉淀析出帶(PFZ)為0.1~0.2 μm，應力腐蝕敏感性最大；T851態下，晶內析出相主要為細小彌散的S′相，合金具有最高的抗拉強度，達到502.01 MPa，晶界析出相呈離散狀分布，PFZ較窄，約為0.02 μm，抗應力腐蝕性能優于T6態的；T351時效狀態下，晶內觀察到大量的位錯和位錯塞積以及少量GPB區，抗拉強度為469.73 MPa，介于T6和T851之間，晶界無粗大平衡相析出，無明顯PFZ，抗應力腐蝕性能最好。
The microstructure and stress corrosion cracking (SCC) sensitivity of aluminum alloy 2056 were investigated using OM, SEM and TEM observations and slow strain rate tension testing (SSRT) in T6, T851 and T351 conditions. The results show that, in T6 aging condition, the coarsening S′ phase and small amount of coarsening Mn-containing phase are mainly observed in matrix, the ultimate strength of 2056 alloy is 445.13 MPa. The grain boundary precipitates are coarsely and sparsely distributed, and the precipitate free zone (PFZ) is 0.1?0.2 μm. In T6 condition, the stress corrosion cracking sensitivity of 2056 alloy is the largest. In T851 condition, the precipitates are high density of S′ phase in matrix, the ultimate strength of 2056 alloy is 502.01 MPa. The grain boundary precipitates are smaller obviously and discretely distributed, and the PFZ is about 0.02 μm, the corrosion resistance is higher than that in T6 condition. In T351 aging condition, the dislocation pile-up and small amount of GPB zones are observed in matrix, and there are no precipitates and PFZ in grain boundaries. In T351 condition, the ultimate strength of the 2056 alloy is between those of T6 and T851, reaching 469.73 MPa, and the alloy possesses the best resistance to SCC.
獲取更多我們供應的合金和服務信息，請致電086-021-67660801或發電子郵件kefu@ailiaigroup.com聯系我們，您也可以通過微博和微信和我們互動。
For more information on the alloys and services that we supply,?call us?at 086-021-67660801 or email us at kefu@ailiaigroup.com. You can also get in touch on social media, we are constantly active on?Weibo?and?Weixin.
前一頁：真空去應力退火對TC18鈦合金殘余應力及組織性能的影響
后一頁：應力時效對2E12鋁合金的力學性能和微觀組織的影響